Q235 High Air Flow Energy Saving Air Supply Centrifugal Flow Fan Introduction The 5-12 series centrifugal fan is an enhanced version of the 5-11 series medium pressure centrifugal fan. Mainly to meet the dust emission requirements of the electric arc furnace exhaust gas purification equipment, improve the workshop environment, to ensure that the dust concentration in the electric furnace working area meets the “sanitary standards for industrial enterprises”, and can also be

Q345 Medium Pressure Antiwear Drying Centrifugal Flow Fan Introduction 1. It is capable of outputting a higher outlet pressure while providing more gas flow with lower noise. Stable operation at higher media temperatures. 2. The fan speed can be flexibly set by matching different pulley diameters to make the fan run at the highest efficiency point and reduce energy waste. 3. Motor sliding guides are provided for easy tensioning of the belt to reduce energy loss due to belt

Single Inlet High Temperature Fluidized Bed Boiler Centrifugal Flow Fan Introduction This series of fans can also be used for dust removal, mine ventilation and general ventilation systems. The blower delivers air, and the induced draft fan delivers flue gas or gas containing foreign particles. It can be used for more than four years when the concentration of impurities is less than 200 mg/m3. If it contains a lot of impurities, it also can be used, but it will shorten the

Carbon Steel Industrial Forward Exhaust Centrifugal Flow Fan Introduction The 8-17 series high-pressure small-flow fan is designed for applications requiring high pressure. Under the premise of ensuring a certain amount of air, the full pressure can reach the high pressure requirement. It is mainly used for blasting furnace blast and other forced air supply, and can also be used for tunnels to exhaust or supply air through hard pipes. Technical data series model Rotation

Alloy Steel High Air Flow High Wear Resistance Drying Centrifugal Flow Fan Introduction At present, there are many series of boilers, and the situation of burning coal quality is quite different, after installing dust removal equipment and waste heat utilization equipment, insufficient pumping force affects normal operation. In order to overcome the insufficient pumping force due to the above reasons, the furnace has a positive pressure, which affects the combustion and

HG785 Alloyed Steel Medium Pressure Backward Mine Ventilate Centrifugal Flow Fan Introduction 6-04 series fans have high pressure coefficient, low peripheral speed, low noise, flat performance curve and wide area of high efficiency. They are used in forging furnaces and high pressure forced ventilation and are widely used to transport materials and air. The maximum temperature should not exceed 250 degrees Celsius. Suitable for flow and dust removal ventilation systems in

High Pressure Alloy Steel Coupling Driven Air Supply Centrifugal Flow Fan Introduction 1. It can output very high pressure and can work at higher medium temperature, suitable for any industrial occasion where high pressure & high temperature gas needs to be delivered. 2. In the case of using the common base , the installation is very simple and basically does not require the support of professional technicians. 3. The bearing box is reserved with the temperature and vibration

Large Capacity Long Lifetime Backward Materials Drying Centrifugal Flow Fan Introduction 1. It can output very high pressure and can work at higher medium temperature, suitable for any industrial occasion where high pressure & high temperature gas needs to be delivered. 2. In the case of using the common base , the installation is very simple and basically does not require the support of professional technicians. 3. The bearing box is reserved with the temperature and

Q345 Industrial Heavy Duty Single Suction Cooling Centrifugal Flow Fan Introduction 1.The fan can output higher gas pressure, and can provide more gas flow at the same time, low noise. 2. In the case of using the common base, the installation is very simple and basically does not require the support of professional technicians. 3. The motor shaft is elastically connected with the drive shaft. It is not necessary to tighten the belt or replace the belt frequently, and the

High Volume Backward Curved CFB Boiler Centrifugal Flow Fan Introduction The 9-10 series high pressure fan is generally used for forging furnace and high pressure forced ventilation and widely used for material transportation. It is suitable for conveying air and non-corrosive, unnatural and non-viscous gases. The temperature of the medium is generally not more than 80°C, and the dust and hard fine particles contained in the medium are not more than 150mg/m3. The fan can also

Aluminium Alloyed Energy Efficiency Smelting Furnace Centrifugal Flow Fan Introduction The 9-10 series high pressure fan is generally used for forging furnace and high pressure forced ventilation and widely used for material transportation. It is suitable for conveying air and non-corrosive, unnatural and non-viscous gases. The temperature of the medium is generally not more than 80°C, and the dust and hard fine particles contained in the medium are not more than 150mg/m3.

China Coupling Driven Anti-Explosion Centrifugal Flow Fan Introduction The fan pressure is high, therefore it is especially suitable for 1-20t/h industrial boilers, which equipped with spiral pipes and multi-tube dust collector.The induced draft fan is made into a single suction, different impeller diameter from 400mm to 3000mm.The position of the air outlet of the fan is expressed by the angle of the air outlet of the casing."Left" and "Right" can be made into different

Single Suction V-Belt Driven Smoke Exhaust Centrifugal Flow Fan Introduction The 7-07 series high-pressure centrifugal fan has a high output pressure, can transport normal temperature or high temperature various gases and various forms of materials, and also can be used in harsh working environments. Such as conveying high temperature/harmful/dangerous gas, hard particles, powder, debris, fiber, forced ventilation, industrial dust collectors, air filtration systems, flue gas

Garbage Incinerator Q345 Anti Abrasive Air Circulation Fan Centrifugal Introduction This series fan can meet the performance requirements of large flow and high pressure at the same time, and has the characteristics of high efficiency and low noise. It is a series of centrifugal fans with a wide range of performance. 6-03 series medium pressure fans can be used to transport normal temperature or high temperature clean gas, dusty gas, flammable gas, corrosive gas, powder or

Carbon Steel AC Motor High Air Flow Ventilation Cengtrifugal Blower Fan Introduction It has large flow and low noise, more use in building ventilation, ventilation and drying of materials, air purification and industrial waste gas treatment, industrial dust collectors, air purification and discharge in hazardous working environments(Paper production line, electrolytic aluminum production line, textile factory...). Blasting of boilers and brick kilns, transport of various

Aluminium Alloyed Single Inlet Large Capacity Exhaust Centrifugal Flow Fan Introduction The 4-16 series centrifugal Fan can be used for indoor ventilation in general factories and large buildings. It can be used as both an input gas and an output gas. The type of gas transported is air and other non-self-igniting, non-self-explosive, non-surrounding, harmless to the human body and is non-corrosive to steel materials. It can also be made into explosion-proof and flame

Alloy Steel V-Belt Driven Backward Curved Cooling Centrifugal Flow Fan Introduction It can also be made into explosion-proof and flame-retardant type according to the requirements of use. It is suitable for occasions with flammable, explosive and corrosive gases. No viscous substances are allowed in the gas, and the dust and hard particles contained in the gas are not more than 150 mg/m3. The gas temperature does not exceed 80°C, and similar gas properties are also available.

Long Lifetime Low Pressure High Wear Resistance Centrifugal Flow Fan Introduction The 5-12 series centrifugal fan is an enhanced version of the 5-11 series medium pressure centrifugal fan. It has a larger output flow than the 5-11 series. It is also used to transport a variety of common gases and hard materials in the industrial field, the application object is exactly the same as 5-11 series fan. Mainly circulating fluidized bed system, smoke exhaust, material drying,